Okay, I've been putting off doing a HOWTO here because, frankly, I'm not really a great seamstress. I've never taken a formal class, and every time I read an issue of I say to myself "Huh! That *would* be a better way to do that." But I figured I'd post this one, for a couple reasons. First of all, even though I'm not that great at it (nothing like , for one, or , for another!) I really do enjoy sewing, and so at least I can reassure people than even if you aren't couture-caliber you can make stuff that fits and have fun doing it. Secondly, I figured if I post this people will tell me what I did wrong, and that way next time I can do it faster/better/more attractively. And finally, I just HATE PATTERNS THAT DON'T HAVE POCKETS. So by posting this I can rescue one more pattern from the evils of pocketlessness.
Anyway. There it is.
So, what will you need to do this project?
- a sewing machine
- an iron and ironing board
- flat space to work
- scissors, tape measure, ruler, pencil or marking implement, etc. etc.
- Diet Coke or similar beverage
- music with a good beat but off-kilter or oddly nihilistic lyrics (I like Soul Coughing, They Might Be Giants, Magnetic Fields, etc.)
- fabric (about two yards of 45" wide for the pattern shown here, 1 3/4 yards if it's 60" wide)
- a suitable pattern (see below)
(Okay, okay, OKAY. I know that pattern has gauchos. Ignore them. Pretend they aren't there. It's okay, we won't even be TOUCHING those pieces. Don't worry. Would I lead you into gauchos? You can trust me.)
Now, pretty much any skirt pattern with a center panel and two side panels will work for this project. I chose this Simplicity pattern because 1) I like contour waistbands and 2) it was $1 at JoAnn's on Saturday, so I could buy two. Why two? Because I'm lazy, and part of this project involves doubling a pattern piece. This way I could just use another part from the second pattern, and not have to trace it. $1 is cheap for not having to trace!
For this project I decided to use view B of this pattern, which is the blue skirt in the illustration. A, B, and C are basically the same, just differing lengths. The first thing I had to figure out is what size to make, so I could pull those pattern pieces and put them aside.
Now, I have a small waist in proportion to my hips (or a big butt in proportion to my waist, calling Sir Mix-A-Lot) so I checked those measurements, and sure enough, the size that was right in the hips would be too big in the waist. (Also, this pattern is made to be worn 1" below the waist, which I Don't Do.)
Now, I've made a lot of Simplicity skirts lately, including another one with a yoke, and so I grabbed the yoke pattern I knew fit me and laid it over the yoke pattern for this skirt. That confirmed for me that I needed a size 12 waistband but a size 14 skirt. What to do?
Well, I took the pieces for the size 12 waistband and cut them on the 12 line at the top edge, but at the 14 at the bottom edge, fudging between them at the sides, so that it would fit at the waist but still be able to be attached to the size 14 skirt. Then I cut out the rest of the pattern pieces from the pattern sheets, making sure to have *two* side front pieces, one from one pattern and one from the other.
That done, the next thing I had to do was to get rid of the pleats in that side front piece, cute as they are, because I thought they would interfere with putting in pockets. Now, I looked to hell and gone all over the Internet for the "right" way to do this, but I couldn't find any instructions, so this is just my usual half-assery: I took the pattern pieces and taped the pleats shut, tapering all the way down to the edge.
But this made me worry that taking that pleat out would make the hips too narrow, so I decided to measure the hips just to make sure. To do this, I put the pattern pieces together, overlapping the seam allowances, and marked where my hip is (about 9" below my waist, you can see a black mark on the center front piece where I measured this). Then I measured across to make sure there would be enough room for my hips (whew! there was).
That done, it was time to figure out where to place the pocket on the side front piece. I held up the pattern to myself, making sure to place the top of it lower than the waist (because the pattern has a waistband). Then I let my hand fall to where I would want a pocket, and marked that.
Then I cut three of the side front piece, out of a scrap I had lying around:
Why three? Because the pocket in the panel has three parts. There's the part of the skirt above the pocket opening (which also includes the 'back' of the pocket), the part of the skirt below the pocket opening, and the part, not visible, that is the 'inside' of the pocket (which is like a facing on the part of the skirt below the pocket opening).
So I took these three pieces and laid them out. Unfortunately, none of these pictures turned out, and OF COURSE it's the most difficult part of making this. Ugh.
Anyway here are the three pattern pieces you end up with (the skirt, the top and underpocket, and the pocket facing). I cut the facing out of a piece of pattern tissue that I had lying around (literally, it was on the floor). You can use any kind of paper. Do write which is which on the facing piece, though, it saves a lot of heartache later. I don't know how many pocket facings I've made and then thrown away by accident!
So how did I get from three of the same piece to three different pieces? Well, you're cutting the bottom off the bottommost piece of the pocket sandwich (everything below the bottom of the inside pocket seam). You're cutting the top off the topmost piece of the pocket sandwich (everything above the top edge of the pattern — but DON'T FORGET to leave a seam allowance, or your pocket will be 5/8ths of a inch lower on your body than you expected). Then you cut the same top and bottom off the pocket facing (the middle part of the pocket sandwich) to make the pocket facing.
The darker blue is the bottommost layer, towards t
he top of the skirt. You can see how deep the pocket will be (the pin) and the black line shows the added seam allowance for the bottom pocket seam (yes I draw on fabric with china markers).
Here's me making sure the pocket is exactly where I want it (the floral thing there is my keychain clipped to the pocket of the skirt I'm actually wearing, as opposed to the one I'm making):
(This is from my point-of-view, e.g., leaning over and upside-down.)
I was happy with this, so then I figured I could make a "real" (that is, wearable) skirt! Yay! But I still didn't want to use great fabric, so I used a piece of lightweight denim I had hanging around. Here's the three back pieces all sewn together:
(I left the pleats in at the back.)
But the plain denim fabric seemed a little boring to me. How could I spice it up? I know! Zippers! Yellow zippers!
You see, when you make this kind of pocket, the top edge can be all wiggly and pulled out of shape, unless you reinforce it with twill tape. Zippers have built-in twill tape, and they make a nice design element.
So get a plastic separating zipper (like the kind that you use to make jackets with). Cut away the teeth of the zipper that would go in the seam allowance (about 1/2 inch on either side, as in the photo above) — you do NOT want the sewing machine needle to hit a zipper tooth!
Of course, the picture of sewing the zipper trim on to the skirt piece didn't come out, either, but what I did was: sew the zipper to the skirt piece, teeth facing down towards the hem. Sew the pocket facing to the skirt piece, right sides together. Then turn and topstitch, like so:
When you're done, it will look like this:
Then, to assemble, you want to attach the underpocket to the pocket facing piece, like so:
I seamed the bottom (this picture is fuzzy) and then double-zigzagged the edges, because this fabric is a bit ravelly.
Then you baste the whole sandwich together. (When you're sewing over the zipper part, even though you trimmed away the teeth in the seam allowance, you probably want to hand-crank the machine. Hitting zipper teeth at speed is Not Fun.)
This is what it looks like when you're done:
See how the stitching down the side is within the seam allowance? I used to baste at the seamline and then had to pick out the bits that showed. I'm marginally smarter now.
Then you do it all again for the other side. Here's the front assembled:
NOTE: Do not let your iron run over the plastic zipper teeth. They WILL melt!
Then you keep going and assemble the rest of the skirt. Here's the waistband going on — why did I sew a line of stitching around the bottom of the waistband facing?
This is why — it makes a nice guideline for turning it under!
Now, time to baste in the zipper. If I'd been thinking, I would have bought a bright yellow zipper for the side zip, too, but I wasn't thinking (and in fact the other zippers were bought more than a year ago for another project), so blue it is.
And actually, my first try at sewing in the zipper was completely crappy, but I offer it here to you to show you how bad a sewer I can be:
So I took it out and redid it (and I re-threaded the machine in blue, because no sense in drawing attention to the zipper!). But this is getting really long, so here's where we skip to the end:
The pockets aren't really uneven: I'm just standing funny. And the skirt is a bit too long; I think I'll shorten it by about two inches next time I make this. It's a bit dowdy at this length.
The whole process (not counting the time it took me to find & buy the pattern) was about three and a half hours. Two hours to do the measuring, planning, preliminary cutting, and prototyping, and one and a half hours to make up the whole skirt (including cutting out the new fabric and re-doing the side zipper). The skirt is hemmed with yellow bias tape, applied by machine.
I didn't prewash the plastic zipper I used for the pocket trim, because it is made of pure polyester. If I were going to use a vintage zipper (or an upholstery zipper) with metal teeth and a cotton tape, I definitely would have prewashed the zipper. If you had long enough zippers (or were okay with lapping them) you could have also inserted zippers into the long front seams between the panels. You could also use piping, braid, or rickrack to trim the pocket edges.
Okay, that's ONE WAY to make front pockets on a panel skirt. If you have a different way, do leave it in the comments! If I left out an important step (as I am wont to do), ask for clarification in the com
ments! (The plant to my right in the picture (your left) is lavender, so you don't have to ask about it in the comments, and my tights are from H&M, last year. Everything else, ask about it in the comments!)